Lighting & Optical

800-505FCLF is a UV-curable, silicone conformal coating, pottant, or sealant with a secondary, neutral alkoxy moisture cure for enhanced adhesion and shadow cure. This material is specially formulated with a high-hardness, low-energy surface after curing, resulting in a low friction surface that resists dust and dirt pickup in outdoor applications.

800-750TFC is also formulated with a high thixotropic ratio to maintain shape and predictable consistency during dispensing. The UV primary cure reacts in seconds, while the addition of our Fast Cure technology allows the secondary, neutral alkoxy moisture cure to begin within 30 minutes for enhanced adhesion and a complete cure, even in shadow areas.

800-506FC features a UV primary cure and a secondary moisture cure. 800-506FC’s extremely low viscosity allows it to flow easily into even the most complex geometries. 800-506FC will UV-cure to a depth of 5mm in a single pass.

800-751TFC features an uncured viscosity of 35,000 cPs, providing greater control and precision during dispense. UV primary cure and secondary moisture cure. 800-751TFC will UV-cure to a depth of 5mm in a single pass.

800-754 is a UV-cure only pottant that cures to a soft, compliant elastomer that relieves stress and strain on delicate components. 800-754 will UV-cure to a depth of 14mm in a single pass.

800-755 is an incredibly soft non-corrosive, single-component gel and is an ideal pottant or encapsulant that will also dramatically increase your throughput.

800-245 is a UV-cured conformal coating. Its moderately flowable viscosity easily coats complex geometries. Fully cured with UV light only (no secondary cure), this silicone offers moderate hardness with good electrical properties.

800-620 is a very soft, clear, encapsulant/gel, designed to maximize vibration damping. It is a low strength silicone with limited adhesion which reduces strain on delicate components. UV only cure.

800-255 is a first-generation pin connector sealant. Its oxime secondary moisture cure provides improved physical properties. The oxime moisture cure can present potential corrosion issues in enclosed applications.

800-260 is a first-generation conformal coating for printed circuit boards. While its oxime secondary moisture cure provides improved physical properties, it offers limited adhesion and can present potential corrosion issues in enclosed applications. This silicone is rated UL 746 E, V-1.

With viscosity of 50,000 cPs, 800-750 clings readily to components for staking and glob-top applications. This non-corrosive, single component silicone will cure to an extremely soft elastomer in seconds upon exposure to UV light, making it ideal for stress and strain relief as well as protection of delicate circuits. It has a secondary, neutral alkoxy moisture cure for enhanced adhesion and shadow cure.

800-230 offers design engineers a higher viscosity coating option, while still remaining flowable. 800-230 is an ideal staking material for securing small components against vibration. It is a UV only cure, providing limited adhesion.

800-235 is UV-cured, semi-flowable material. A UV-cure only silicone with limited adhesion, its higher viscosity makes it ideal for cured-in-place gaskets.

800-240 is a UV-cure only, semi flowable material similar to 800-235. 800-240 offers higher hardness and abrasion resistance with good elongation and electrical properties.

800-400 is a UV-only, fast-curing paste without adhesion. With nominal viscosity of 360,000 cPs, 800-400 consistently holds its shape even when dispensed into complex shapes.

800-610 is a low viscosity, pourable encapsulant. Its extremely low viscosity ensures the material flows easily around components for thorough wet-out. This is a UV cure with no secondary moisture cure, offering very low adhesion.

800-520FC is a UV-curable, silicone conformal coating, pottant, or sealant. This version of our original 800-520 coating utilizes Fast Cure technology to begin moisture cure of shadow areas in as little as 30 minutes, and provides a harder, more durable surface than our standard 800-520.

800-505FC is a UV-curable, silicone conformal coating, pottant, or sealant. It has a secondary, neutral alkoxy moisture cure for enhanced adhesion and shadow cure. Utilizing our Fast Cure technology, this secondary moisture cure begins in as little as 30 minutes and can develop full adhesion in hours.

500-210 is a balanced-performance silicone coating featuring a room temperature alkoxy moisture cure that can be accelerated with heat. Soft enough to reduce strain on components while being tough enough to resist abrasion.

500-224 is an is an opaque, single-component silicone coating and encapsulating compound that cures at room temperature to form an extremely tough, strong, abrasion-resistant coating that completely hides your circuitry and components.

500-211 is a compliant, optically clear coating.

500-222 is a tough, optically clear conformal coating and encapsulant that remains flexible and non-brittle.

500-223 cures to an extremely soft, optically clear gel to provide maximum stress and strain relief in addition to great dielectric properties.

500-228 cures to a tough, strong, resilient gel to provide protection from both physical damage and mechanical stress and strain relief in addition to great dielectric properties.

500-090, 500-091, and 500-092 are a family of UL-rated electronics adhesives. These one-part UL flame rated pastes are for applications that require superior bond strength and flame resistance.

500-607 is a soft, very low viscosity clear pottant that flows easily into intricate architectures and complex designs, with low shrinkage and long working times.

600-160 is a two-component, addition-cure silicone that, when mixed, cures to a flexible elastomer.

600-170 is a two-component, addition-cure silicone that, when mixed, cures to a flexible elastomer.

600-180 is a two-component, addition-cure silicone that, when mixed, cures to a flexible elastomer, formulated with moderate elongation and exceptional tensile strength.

HT-70UL is a low density, high temperature closed cell foam for industrial applications.

70P UL is a low density closed cell PVC foam formulated to conform to UL HF-1/HBF for use as an ANSI/UL94 approved component in electronic applications.

HT-70UL is a low density, high temperature closed cell foam for industrial applications.

400-100 is a single-component, moisture-curing silicone paste that cures to a low to medium modulus, rubber-like solid.

400-102 is one of our single-component, moisture-curing silicone pastes that cures to a low to medium modulus, rubber-like solid.

400-103 is a non-flowable, non-sagging paste product presenting an excellent balance between rate of cure, adhesion, and physical properties.

400-150 is one of our single-component, moisture-curing silicone pastes that cures to a low to medium modulus, rubber-like solid.

400-195 is a non-flowable, non-sagging paste product that provides a fast tack free time and high green strength.

400-196 is a non-flowable, non-sagging paste product that provides a fast tack free time and high green strength.

400-202 is a non-flowable, non-sagging paste product that provides a fast tack free time and high green strength.

400-590 is a smooth, black paste that is ideal for applications that require superior bond strength and moisture resistant sealing in automotive and industrial arenas.

400-110 is a non-flowable, non-sagging paste product that is ideal for industrial applications that require superior bond strength and moisture resistance.

400-118 is a non-flowable, non-sagging paste product that is ideal for industrial applications that require superior bond strength and moisture resistance.

400-155 is a non-flowable, non-sagging paste product that is ideal for industrial applications that require superior bond strength and moisture resistance.

400-900 is a non-flowable, non-sagging low-adhesion paste ideal for creating formed-in- place gaskets where re-entry or post production disassembly is necessary.

400-950 is a non-flowable, non-sagging low-adhesion paste ideal for creating formed-in- place gaskets where re-entry or post production disassembly is necessary.

200-251 is a single-component, oxime-cure silicone for use in applications where the coating needs to flow into small crevices and hard to reach areas.

200-260 is a single-component, oxime-cure silicone for use in applications where the coating needs to be sprayed or to flow into small crevices and hard to reach areas.

200-202 is a single-component, oxime-cure silicone for use in applications where the coating needs to flow into small crevices and hard to reach areas.

Ready-to-use, 200-250 is an oxime-cured silicone used for general industrial sealing and bonding applications requiring a flowable product.

200-102 is a single-component, oxime-cure silicone for use in applications where the coating needs to settle into small crevices and hard to reach areas while maintaining consistency without sagging or running.

200-107 is a single-component, oxime-cure silicone for use in applications where the coating needs to settle into small crevices and hard to reach areas while maintaining consistency without sagging or running.

200-257 is a single-component, oxime-cure silicone for use in applications where the coating needs to settle into small crevices and hard to reach areas while maintaining consistency without sagging or running.

70P UL is a low density closed cell PVC foam formulated to conform to UL HF-1/HBF for use as an ANSI/UL94 approved component in electronic applications.